Best Treestands – Climbing Sticks & Tree Steps for the money

The quick stick XL climbing sticks are made of durable steel tubing and come in the muddy powder coat making for a long-lasting finish. These sticks are 48 inches long per section. And come in sets of five the steps are ten. And a half inches wide. And attach to the tree with silent cam buckles. Each section weighs five pounds. And has steps on both sides the quick stick XL climbing sticks are a straightforward climbing system. That gets you 220 feet up.

after unpack aging the box you'll find the stand along with a manual. And safety DVD a parts bag with strap bolts nuts. And washers the M 102 s receiver at EMA approved safety harness. And nice touch a lifeline assembly is really simple attach the upright to the base with the three-inch bolt — orange washers to regular washers. And the not take note. That the orange washers go against the upright not the regular ones snug. It up good but it still has to bend without a lot of effort next install the seat using a four. And three-quarter inch bolts — washers in. One night please take note. That the orange washers are already installed in. This step the seat should move freely but still have. Some resistance to hang the stand first install the m102 s receiver to the tree by attaching the ratchet strap to the receiver via the bolt on the right side make sure top is up before securing to the tree completely next slide the standards at the receiver removing the art clip first. Once the stand is seated properly reinstall the our clip. You can attach the lower ratchet strap to the upright near the base tighten. And secure properly to adjust the platform simply lift up on the base to take tension off pull the locking bracket out of position. And slide to the next desired position.

This is going to allow. You to level the base to the tree. You are hung in the seat will lift out of the way. And there's also a bolt. You can move in and out to adjust the level of the seat along with the adjust ability of the seat. It is also very large. And very comfortable the platform is a really good size. It allows a lot of freedom of movement to get set up for. That perfect shot included in the purchase of. This stand are straps to pack the stand in. And out the included footrest is already installed. And is set at a nice angle for all-day comfort the size of the foot grading on the base. And the overall finish of the stand is on par with.

All other top manufacturers the m50 by millennium is a really nice hang on stand in my opinion for a little over a hundred dollars. You get a very nice wide comfortable seat a huge platform to move around on a building footrest for all-day comfort. It comes with a lifeline. They do provide backpack straps. You could pack this stand in. And out at 20 pounds. Ifeel it's a bit heavy for a run-and-gun application but for the reason. Ibought it to hang. It sits for the whole season. Or maybe only end up moving at. One time this is a really nice stand for your money so go check them up.

Good morning I'm David McCool with hurricane safety systems. And I'd like to introduce to. You today our flagship product it's a tree stand attachment system called the tree stand power lock by hurricane safety systems basically. What this is essentially is a device. That we've developed after the glass two years. It is a tensioning device. You can see here basically. How this works is and you'll you'll see. This square frame is simulating a tree stand frame we've developed a couple Universal brackets. That attach to the tree stand frame. And we also have one for a center post but. You don't see that here so here are the brackets the tensioning device the power lock itself can be used with a drill. Or a ratchet I'm gonna back. It up here so you can see. This pretty clearly. This is the tensioning device again we've been in development of. This for about two years within the tensioning device. What we've created is a micro plush. And this micro clutch provides. What we call calculated radial extraction that's the amount of force. That we are sucking the tree stand to the tree so as. You can see it's got a very healthy size sturdy hook on. It and what happens is. These universal brackets. That you would attach to your stand the power lock simply clips in as. You can see here and the gearing in. It is fantastic we say I'm. Even tightening with my fingers. You can use a ratchet a wrench of. Any kind to do this so. You open the tree simply take our chain pass. It around the tree I'm going to use the drill with.

This thing you're gonna see. That the micro clutch is very similar to the clutch. That you find in a drill so. If you've got a preset amount of clutch. Where this thing punches out you'll get feedback. Imean audio feedback on. It you're going to hear. That with this product right. Now I'm going to show. It to you we simply just start. It you can see the cable is coming in is retracting in. We come forward on it. And you hear that the minute. You hear that that means. That our power lock has flushed out at about 400 pounds again of calculated radial extraction so the advantages of. This very safe product. Because you're working in front of. You're not reaching around the tree to pull the strap tight getting off you're always working in front of. You have left-to-right adjustment.

Now we're advocating. That you use your strap. That the power lock is a backup system but. We believe it is the world's. Most technically advanced safest tree stand attachment system. And we're very proud to bring it to market for more information please contact hurricane safety systems. You can go to the web. And find us there or w/e hurricane SS com.

after unpack aging the box you'll find the stand along with a manual. And safety DVD a parts bag with strap bolts nuts. And washers the M 102 s receiver at EMA approved safety harness. And nice touch a lifeline assembly is really simple attach the upright to the base with the three-inch bolt — orange washers to regular washers. And the not take note. That the orange washers go against the upright not the regular ones snug. It up good but it still has to bend without a lot of effort next install the seat using a four. And three-quarter inch bolts — washers in. One night please take note. That the orange washers are already installed in. This step the seat should move freely but still have. Some resistance to hang the stand first install the m102 s receiver to the tree by attaching the ratchet strap to the receiver via the bolt on the right side make sure top is up before securing to the tree completely next slide the standards at the receiver removing the art clip first. Once the stand is seated properly reinstall the our clip. You can attach the lower ratchet strap to the upright near the base tighten. And secure properly to adjust the platform simply lift up on the base to take tension off pull the locking bracket out of position. And slide to the next desired position.

This is going to allow. You to level the base to the tree. You are hung in the seat will lift out of the way. And there's also a bolt. You can move in and out to adjust the level of the seat along with the adjust ability of the seat. It is also very large. And very comfortable the platform is a really good size. It allows a lot of freedom of movement to get set up for. That perfect shot included in the purchase of. This stand are straps to pack the stand in. And out the included footrest is already installed. And is set at a nice angle for all-day comfort the size of the foot grading on the base. And the overall finish of the stand is on par with.

All other top manufacturers the m50 by millennium is a really nice hang on stand in my opinion for a little over a hundred dollars. You get a very nice wide comfortable seat a huge platform to move around on a building footrest for all-day comfort. It comes with a lifeline. They do provide backpack straps. You could pack this stand in. And out at 20 pounds. Ifeel it's a bit heavy for a run-and-gun application but for the reason. Ibought it to hang. It sits for the whole season. Or maybe only end up moving at. One time this is a really nice stand for your money so go check them up.

This is the extant tree stand. This is the world's lightest two-piece climbing tree stand hi my name is Tony over ball. And I'm here to demonstrate the use of the extant restain. You can see how the x10 packs on your back for easy backpacking it comes with shoulder straps already attached. And the next thing you want to do just take. It off your back I usually lean. It up against the tree. And remove the budging unclip the backpack straps from the clip bubbles. And the two pieces separate easily. How to attach the X stand to the tree first twist the pin to unlock. It pops the cable out pull. It through the loop wrap. It around the tree pull the pin pop the cable in give it a twist to lock. It to attach the bottom platform it's the same as the top twist to unlock pull the pin pop the cable out wrap the cable around the tree put. It back through the loop pull the pin pop. It in place twist it to lock. You would reattach your tether straps like. You easily be adjusted. You connect them for climbing make sure. You take out all the slack. You want as much length as possible be sure to always start your stand with an upward angle.

Because as the tree tapers. It will level out before. You ever leave the ground be sure to be connected with a harness. That has met TMA standards. All right now you're ready to climb. Once your stand has been attached your tethers have been connected. You checked all your pins. Everything is secure the seat is designed to be raised up so. You can put your hands under. And grasp the frame lift the upper part the seat portion lock. It into place placing your elbows on these pads. And grasping the frame put your feet into the foot stirrups spread them apart to take up the slack the X stand tree stand is what's commonly known as a hand climber do not sit on. This rail it as a sit. And climb always grasp the frame get up use your elbows to support your weight going up. Or down never sit on. This rail the foot strap on your X stand designed to be stepped on. And flattened out but. It is also designed for hands-free operation slide your feet through the strap spread them apart take up.

Any slack this will allow. You to comfortably maneuver the bottom platform. While climbing your feet spread apart raise the platform. And lock it into place to come back down is just a reverse of. That process reset the stand supporting your weight on your elbows lower the platform again just repeat the process the tether straps which are also your backpack straps but in. This case we're using them as a tether they're designed to secure the top part of your stand to the bottom. Once you've reached your hunting height to prevent. This top from sliding pull down on the slide buckle taking up. All the slack this will pull tension on the seat to the same on the opposite side pull. All of the slack out of the strap securing it tight. This will prevent the upper seat part from sliding or moving never allow your stand the slope. Or the downward angle. This happens you must return to the ground.

And readjust and then go back up. If it's slightly unlevel. You can pull the stand to. You pull the slack out of the cables drop the lower part. And correct this never ever detach the cable from the locking pin. While you're climbing always try to take your excess strap. And just tuck it in behind the seat so it's not blowing in the wind attracting attention. And pull a little more slack out after. You sit on the seat to make sure it's tight. Once you've done this correctly. This top portion won't move. It locks it rights into place. Many people are curious about. This Flex arm technology. What this does is as weight is applied to the stand it'll the arms will bend inwards just like. Both limbs it will allow the cable to squeeze the tree.

What makes the stand so stable. And also what makes. It so like we're often asked. How much weight will. These flex arms hold so. This is the demonstration show. That the flex arms don't actually support your weight they're only there to allow the cable to flex in. And open the cable loop for easy climbing so. What I'm going to do is take the cable completely out just put. It around the tree without using the Flex arms at. This demonstration to show. These flex arms do not support your weight they're only there to guide the cable. And to open and close the loop for easy climbing as. You can see the stand will easily support my weight without. Even being attached to pack your X stand up for backpacking just unzip your strap remove the sand from the tree same process just in Reverse as.

It on — pack your ex stand-up for backpacking take the seat portion nest. It together with the bottom platform next attach your funding board to hold the two sections together three attach your backpack straps by pulling your clip buffle through the same rung. That your foot strap is attached to clip the buckle in. And pull out the slack do the same on the opposite side pull the buckle through the frame slip them together pull out the slack. You have your backpack strap it's very quick. And easy to do once the stand is on your back. You can pull on these straps using the slide buckles to tighten. It up do not cut away. This excess strap it's needed. These are being used for tethers to climb with just tie. It off in front that you've watched.

This video and you've read. And understood all the instructions. That come with your X tender. And you've attached yourself with an approved fall arrest system you're ready to hunt. This is the extant restain just over twelve pounds it's a rose the lightest two-piece climber

Hi I'm Travis Macaulay with extant tree stands I'm here at the 2013 ata show just a little history about our company. This is our fourth year at the ata show the first two years. That we came to this place. We were a really small fish in a great big pond. We come and we have. This one product this is the x1 climbing tree stand. It is the world's lightest climbing tree stand. And this model on the best of the best award in field. And stream now being our fourth year we've grown into. This and of course. We have a lot of other stuff out there the first off let. Me tell you a little bit about the tree stand. That made us famous. Now this stand is unique. And different not only is. It the world's lightest but it's got a lot of other really neat features. This one bungee it comes with the stand in the Box hold your two pieces together your seat in your platform so. All you do is whenever. You take the stand-off the trees. You lay your platform down. And take your seat and lay. It on top of it and. This stand was designed for the seat. And the platform to mesh perfectly together.

And then you take out. One bungee and wrap. It around there and you're. All set up another great feature about. This stand it's whatever. You do have it on your back. And you're walking through the woods. Iknow of a lot of climbing tree stands out there. When you're walking through the woods sometimes. You got to reach back. And hold your two pieces together. Because they're clanging around. And making a lot of noise well. This thing when it's on your back. And you tighten it up it's not making any noise. It can be bouncing off your back. And it's not clanging and banging and making all. That racket it's completely silent. You can tie that off. Or do whatever you want. And to loosen it all. You do is push down on these you're completely loose. And you can take your stand-off. Now come on over here. And I'll show you what it looks like on a tree. Some other really neat features about our climbing tree stand is a quick attach system which is spring-loaded with a rubber-coated pin.

It also we also have a sit. And climb model which is. This model right here it's got a bar. You can sit on you can also use. This bar as a shooting rail an armrest a footrest. Or you can put it up out of the way. If you like our backpack straps second is our tether straps which will hook your platform to your seat. Whenever you're climbing and then. Whenever you get to your destiny. Or hike on your tree. You can tighten these up so. That the locks your see in place our whole concept behind. These limbs over here which are fiberglass kind of like your bow limbs — designed to flex so. Whenever I whenever. You put weight on the platform those flex arms will grab the cable.

And pull it tight to the tree which makes for a. More secure better sit. And then whenever you're climbing with the standing you take your weight off to bring your platform up those flex arms will pull the cable away from the tree. Because you got to get around. Some knots or some sawed off limbs. You know your cables not grabbing all. That stuff and it makes them for a lot easier climbing experience. Another great thing about. This tree stand is our seat it's got four pieces of foam. And it's designed for a very comfortable sit so. You can sit in this thing all day with no problem. This tree stands made out of high-grade aluminum so. It cost us a lot more money to manufacture.

These tree stands and. It does all of our competitors but at the end of the day you're getting what you want it's made out of t6 6061 aircraft aluminum that's. Where we get our lightweight but not only do. We get lightweight we get a sturdy tree stand. They don't rust it's practically weatherproofed. Because it's aluminum, so I'm innocent it's an awesome product we're super excited to be able to get. This thing on the market. And get it in the woods it's a great tool it's. You know for a guy that wants to get out there. And kill some big bucks its good to have a next n on your back. Because you can get deep. You can be quiet you can climb easy. And you have a comfortable sit. Now I'm going to tell.

You a little bit about our hang on Stan new for 2013 weighing in at only 10 pounds uses the same high-grade aluminum as our climate stand the t6 6061 aircraft aluminum not only is. It light but it's also super easy to hame utilizing our five-point hitch system for hanging so no matter. If the trees leaning backwards. Or forwards you can still hang your tree stand on the stand. And sit comfortably with our hitch system. Because you can level the sand. Now I'm going to tell. You a little bit about our super lightweight climbing stick it's super easy to attach to the tree. It utilizes a non-slip step the angles out away from the tree as. You can see there making it easy to get your boot on. It you don't have to worry about your boot hitting the back of the tree so it's super easy to hang it's aluminum so it's super lightweight. And it has a non-slip step with. These grooves in it I'm going to show. You how our climbing ladders. And our hang on fit together.

When you're ready to come out of the woods it's got. This one bungee which is attached to the platform of the hang on sand that'll hold your sticks to a platform make them for easy packing out of the woods. This whole system with four sticks. And your hang on weighs less. Than 20 pounds four years ago. We dropped our competitors jaws by coming in. And the tree stand industry with the world's lightest climbing tree stand which. On the best of the best of the ward in Field & Stream magazine. This year we're dropping their jaws with their all-new ladder stand weighing in at only 45 pounds. This ladder stand is the only. One of its kind you completely set. This thing up before. You ever leave the ground making it. One of the safest ladder stands out there. All you do to hook. This thing up is you leaning against the tree. And you have two galvanized aircraft cable. That drape down on both sides of the tree cross those cables behind the tree.

You run the cables through a loop. And hook them to a hook right there. And turn it and you're. All set up before you ever leave the ground. Once you climb up there's no. More doing that climb of death. Where you're climbing to stand. And then strapping a strap around the tree you're completely set up before. You leave the ground. When you climb up there's. Nothing else left to do. It also is weatherproofed. This thing's made out of aluminum. And there's no ratchet straps. That get beat up by the Sun. Or rain and wear and tear. They don't use any ratchet straps it's weatherproof super light. And you hang it and set. It up before you ever leave the ground. Iwas telling you earlier. That it was weatherproofed well. It is uses a plastic seat up there which is a big chair. You talk about a big comfortable seat man. Icould sit up here.

All day know what I'll have right here is our. All new hunting chair super lightweight. It can be great for getting out in them woods. And getting you a couple feet off the ground. You don't have to worry about having a wet seat. All you do to hook. This thing to the tree it's. That strap will run around the tree just like. This and you just pull. It tight and they don't matter. If you're on a hill. Because all you got to do is pull. That ball out a little further. If you're on a hit downhill. Or an uphill it don't matter. And then you have you a good comfortable seat. And that thing is super light.

Now right here we have our hunting blind its pattern. And mossy oak it uses elongated magnetic windows is great for a family of hunters. Or standing shots filming hunts its wheelchair accessible. You can drive a full wheeler up in. It's super roomy. It only weighs 12 pounds.